PFAS in South Florida Water: What Broward County Homeowners Need to Know in 2026

Broward County has detected PFOA above the EPA's 4 ppt MCL. This guide covers PFAS detection data, EPA standards, which filtration methods remove PFAS (RO: 99%,

By the WaterLux Editorial Team · Published 2026-03-19 · Updated 2026-11-09

PFAS in South Florida Water: What Broward County Homeowners Need to Know in 2026

Last updated: March 2026 by WaterLux Water Systems — serving Broward, Palm Beach, and Miami-Dade Counties since 2011.

Last updated: April 2026 · Reviewed by WaterLux Water Treatment specialists

The short answer: PFAS (forever chemicals) have been detected in Broward County water supplies drawn from the Biscayne Aquifer. The EPA set maximum limits of 4 parts per trillion in 2024, but utilities have until 2029 to comply. A reverse osmosis system removes 90-99% of PFAS from drinking water — it is the most effective residential solution available in South Florida.

PFAS — per- and polyfluoroalkyl substances, often called "forever chemicals" — have been detected in Broward County's drinking water above the EPA's new 4 ppt Maximum Contaminant Level. This guide answers the most important questions South Florida homeowners are asking about PFAS in their tap water, what the regulations mean, and which filtration methods actually work.

Broward County PFAS Data & EPA Standards

What PFAS levels has Broward County detected in its drinking water?

These readings exceed the EPA's 2024 PFAS Maximum Contaminant Level (MCL) of 4 ppt for PFOA. While utility-level compliance schedules allow water systems time to install large-scale treatment, individual households in Broward can act immediately by installing a certified point-of-use or whole-house treatment system. WaterLux recommends annual water quality reports (Consumer Confidence Reports) from your local utility to track trends, and offers free in-home PFAS screening tests.

What are the EPA PFAS Maximum Contaminant Level (MCL) standards?

The EPA finalized its first-ever PFAS drinking water standards in April 2024. The MCL is 4 ppt (parts per trillion) for PFOA and 4 ppt for PFOS individually, with a combined Hazard Index limit for four additional PFAS compounds.

In April 2024, the U.S. Environmental Protection Agency (EPA) finalized the National Primary Drinking Water Regulation for PFAS — the first federal MCLs for these compounds. The standards set maximum contaminant levels at: PFOA: 4 parts per trillion (ppt); PFOS: 4 ppt; PFHxS, PFNA, and HFPO-DA (GenX): 10 ppt each individually; and a combined Hazard Index of 1.0 for mixtures of PFHxS, PFNA, HFPO-DA, and PFBS. Public water systems have until 2027 to comply. These are the most stringent PFAS limits in the world. Homeowners who want protection now — rather than waiting for utility-level compliance — should consider installing a certified reverse osmosis system or activated carbon system rated to remove PFAS.

PFAS Filtration: What Works and What Doesn't

Which water filtration methods remove PFAS, and how effective are they?

Reverse osmosis (RO) is the most effective method, removing 94–99%+ of PFAS. Activated carbon (granular and block) removes 73–95% depending on contact time and carbon type. Ion exchange resins achieve 90%+ removal for most PFAS compounds.

Not all filters remove PFAS. Standard pitcher filters, refrigerator filters, and basic sediment filters do little to reduce PFAS concentrations. Effective options include: (1) Reverse Osmosis (RO): The gold standard, with removal rates of 94–99%+ for PFOA and PFOS. Under-sink RO systems are the most practical for South Florida homeowners and protect drinking and cooking water. (2) Activated Carbon: Granular activated carbon (GAC) removes 73–90% of PFAS; carbon block filters can reach 85–95%. Effectiveness depends on contact time and the specific PFAS compounds present. (3) Ion Exchange Resins: Specially designed anion exchange resins achieve 90%+ removal for short- and long-chain PFAS. Often used in combination with GAC for comprehensive treatment. WaterLux installs NSF 58-certified RO systems and NSF 42/53-certified carbon systems specifically selected for PFAS reduction.

WaterLux PFAS Solutions for South Florida Homes

What WaterLux solutions remove PFAS from South Florida tap water?

WaterLux offers NSF 58-certified reverse osmosis systems (under-sink and whole-house), high-capacity activated carbon whole-house systems, and combination softener + RO packages — all professionally installed with a free water test to identify your home's specific PFAS and contaminant profile.

WaterLux provides several PFAS removal solutions tailored to South Florida homes: (1) Under-Sink Reverse Osmosis Systems: 5–6 stage RO units installed under the kitchen sink, delivering 99%+ PFAS-free water at the tap. Ideal for drinking and cooking. From $499 installed. (2) Whole-House RO Systems: Full-home protection treating all water entering the house. Best for well water users or homeowners with high PFAS contamination. (3) Whole-House Activated Carbon Systems: Carbon pre-filters remove chloramines, VOCs, and a significant percentage of PFAS from all household water. Often combined with a softener. (4) Combination Packages: Whole-house carbon + softener + under-sink RO is the most comprehensive package, addressing hardness, PFAS, chloramines, taste/odor, and other contaminants simultaneously. All systems come with professional professional installation by certified water treatment specialists, WaterLux's 1-year parts/labor warranty, and annual service plans. Call (754) 317-0104 or visit waterlux.com/contact to schedule your free water testing.

General PFAS & Water Safety FAQs

How much does a reverse osmosis system cost in Florida?

Under-sink reverse osmosis systems in Florida cost From $300 for the unit plus From $200 for professional installation, totaling From $500 for most homeowners. Whole-house RO systems—best for well water with very high TDS—range From $4,000 installed. Ongoing filter maintenance runs From $175 per year for under-sink systems.

For South Florida homeowners on city water (like Pompano Beach), an under-sink reverse osmosis system is the most popular choice for clean drinking water. These 5-stage systems remove chloramines, PFAS, nitrates, sodium, and other contaminants not addressed by a whole-house softener, and cost From $3,600 fully installed. Tankless RO systems (no storage tank) run slightly higher at From $1,295 but take up less cabinet space. Whole-house RO systems are primarily used for well water with high total dissolved solids (TDS) or extreme contamination, and Florida pricing typically runs From $8,000 for a quality system given the state's challenging mineral content. Annual maintenance—filter swaps and membrane replacement—costs From $175 for under-sink systems. WaterLux bundles initial filter replacements into all new installations.

Does a water treatment system add value to my home in Florida?

A whole-house water treatment system is a strong selling point for South Florida homes, where nearly every buyer is aware of the region's hard water and chloramine issues. While there is no universal appraisal value increase, installed systems typically earn their cost back at resale and reduce time on market by appealing to informed buyers.

In the South Florida real estate market, a home with a professionally installed, maintained water treatment system is a meaningful differentiator. Buyers familiar with Broward County water quality—hard water with chloramines and detectable PFAS—actively seek homes that already have treatment in place, avoiding the cost and hassle of post-purchase installation. Real estate agents in the area report that water treatment systems, particularly when paired with an under-sink RO drinking water system, are popular disclosure items that ease buyer concerns. From a structural standpoint, protected plumbing and appliances represent genuine added value. WaterLux provides documentation and transfer support when you sell your home, so the next owner can continue benefiting from your system.

Is Pompano Beach tap water safe to drink?

Pompano Beach tap water meets all federal and state Safe Drinking Water Act standards. The city's 2024 Water Quality Report confirmed no maximum contaminant level (MCL) violations across 108 tested parameters. However, meeting legal standards does not mean the water is free of all concerns—Pompano Beach water contains chloramines, low levels of disinfection byproducts (THMs and HAA5s), and detectable PFAS compounds below current MCLs.

Pompano Beach's local water system tests water at over 90 sites monthly and monitors more than 108 parameters. Chloramines (used instead of chlorine for distribution) were detected at standard disinfection levels. PFAS compounds (including PFOA and PFOS) were detected at trace levels consistent with South Florida groundwater. While the water is legally safe, many Pompano Beach homeowners choose a whole-house filter to remove chloramines and an under-sink RO system to address PFAS and other trace contaminants for peace of mind.

Does Pompano Beach water have PFAS (forever chemicals)?

Yes, Broward County water systems have detected PFAS compounds including PFOA and PFOS at trace levels. The 2024 Broward County Water Quality Report showed PFOS at approximately 0.02 µg/L (20 parts per trillion)—below the EPA's proposed 4 ppt MCL in some tests but at levels many water quality experts consider worth addressing. Reverse osmosis is the most effective home treatment for PFAS removal.

PFAS (per- and polyfluoroalkyl substances), often called 'forever chemicals,' are a growing concern in Florida water. A 2024 University of Florida study found PFAS in 63% of Florida freshwater spring samples, and testing of South Florida municipal systems has detected PFAS compounds at varying levels. Broward County's 2024 report lists PFOA at approximately 0.007 µg/L and PFOS at approximately 0.020–0.024 µg/L. The EPA's proposed MCL (4 parts per trillion or 0.004 µg/L) means these levels approach or exceed the new standard in some samples. Florida does not yet have its own PFAS MCL, but is required to adopt the federal standard by 2027. A properly maintained under-sink reverse osmosis system removes 90–99% of PFAS compounds and is the most cost-effective home solution for families concerned about forever chemicals. WaterLux recommends annual water testing to stay informed about current PFAS levels at your tap.

What contaminants are in South Florida drinking water?

South Florida municipal water typically contains chloramines (disinfectant), disinfection byproducts (THMs and HAA5s), trace PFAS compounds, sodium (from saltwater intrusion), fluoride, and hardness minerals (calcium and magnesium). Well water in Broward County often also contains elevated iron, hydrogen sulfide (rotten egg odor), and higher TDS. All of these can be addressed with the right combination of water treatment equipment.

These are all within legal limits but represent a diverse set of contaminants that different treatment technologies address. Whole-house carbon filters target chloramines and disinfection byproducts. Water softeners address hardness (calcium and magnesium). Reverse osmosis addresses PFAS, sodium, nitrates, arsenic, and fluoride. WaterLux offers comprehensive water testing to identify what's actually in your water and designs a system that addresses your specific contaminants—rather than selling a one-size-fits-all package.

Is softened water safe to drink?

Yes, softened water is safe to drink for most people. A water softener adds a small amount of sodium during the ion exchange process—approximately 20–30 milligrams per 8 oz serving for water that was very hard. This is less sodium than a glass of low-fat milk. People on sodium-restricted diets should pair their softener with an under-sink RO system, which removes sodium along with other contaminants.

The ion exchange process in a water softener replaces calcium and magnesium ions with sodium ions. The amount of sodium added is proportional to the original hardness level. For Broward County water at 10 GPG, a typical 8 oz serving of softened water contains approximately 25–30 mg of sodium—well below the FDA's 'low sodium' threshold of 140 mg per serving. The American Heart Association and most healthcare providers do not restrict softened water for healthy individuals. However, for people with diagnosed hypertension or heart disease who must follow a strict low-sodium diet, WaterLux recommends adding an under-sink reverse osmosis system for drinking and cooking water—RO removes over 95% of sodium from softened water, delivering mineral-free water at the tap.

What is the difference between water hardness and water quality?

Water hardness refers specifically to the concentration of dissolved calcium and magnesium—it is a measure of mineral content, not safety. Hard water is not harmful to drink but causes scale buildup, soap inefficiency, and appliance damage. Water quality is a broader term covering all contaminants including bacteria, chemicals, heavy metals, and PFAS. A water softener addresses hardness; a full water quality assessment requires testing for multiple parameters.

Many homeowners in Pompano Beach confuse hard water with unsafe water. Hard water means your water has elevated levels of calcium and magnesium—minerals that are not toxic and are actually essential nutrients. The problems hard water causes are economic and aesthetic: scale deposits in pipes and water heaters, spotted dishes, stiff laundry, soap scum, and dry skin. Water quality in a safety context refers to levels of regulated contaminants like lead, nitrates, bacteria, PFAS, arsenic, and disinfection byproducts. You can have hard water that is otherwise excellent quality, or soft water that contains concerning levels of other contaminants. This is why WaterLux always starts with a comprehensive water test—it identifies both hardness and other water quality parameters—before recommending any equipment.

How does reverse osmosis work?

Reverse osmosis (RO) forces water under pressure through a semi-permeable membrane with pores so small (0.0001 micron) that dissolved contaminants, heavy metals, PFAS, nitrates, sodium, and most other impurities cannot pass through. Clean water collects on one side; concentrated contaminants flush to the drain. The result is exceptionally pure water—typically 90–99% free of dissolved solids.

A standard 5-stage under-sink RO system used by WaterLux works as follows: Stage 1 (sediment pre-filter) removes particles, rust, and sediment that would clog the membrane. Stage 2–3 (carbon block filters) remove chlorine, chloramines, and organic chemicals that would degrade the membrane. Stage 4 (RO membrane) is the core of the system—water molecules pass through under household pressure while dissolved contaminants are rejected and flushed to drain. Stage 5 (post-carbon polishing filter) removes any residual taste before water enters the storage tank. Membranes typically last 2–3 years; pre and post filters should be replaced annually.

What does reverse osmosis remove from water?

Reverse osmosis removes 90–99% of most dissolved contaminants, including PFAS (forever chemicals), lead, arsenic, nitrates, fluoride, sodium, chromium, radium, and most dissolved solids. It also removes chloramines, disinfection byproducts, pharmaceutical trace compounds, and other organic chemicals. RO is one of the most comprehensive water purification technologies available for home use.

For Pompano Beach and Broward County homeowners, an under-sink RO system addresses multiple water quality concerns in one unit. Verified removal rates for common South Florida concerns: PFAS (PFOA/PFOS) — 90–99% removal; arsenic — 90–95% removal; sodium — 90–95% removal (important for saltwater-influenced municipal water); nitrates — 85–95% removal; fluoride — 85–92% removal; chloramines — removed by pre-filters and membrane; lead — 95–99% removal; TDS reduction — typically 90–97%. RO does not effectively remove dissolved gases (like radon or hydrogen sulfide) or certain volatile organic compounds without carbon pre-filtration. It also does not soften water (reducing hardness GPG); a separate water softener is still recommended for whole-house scale protection. The ideal South Florida setup pairs a whole-house softener + carbon filter with an under-sink RO for drinking water.

What is the difference between under-sink and whole-house reverse osmosis?

An under-sink RO system (point-of-use) filters drinking and cooking water at a single faucet—ideal for most South Florida homeowners on city water who want pure drinking water at a reasonable cost (From $1,295 installed). A whole-house RO system filters every drop entering the home and is used primarily for well water with very high TDS, contamination, or when bathing water quality is also a concern (From $8,000 installed).

For Pompano Beach homeowners on municipal water, an under-sink RO system addresses the most important exposure route—drinking and cooking—at a cost of From $1,295. Paired with a whole-house carbon filter and water softener, this creates a comprehensive three-layer treatment approach: softener removes hardness (protects plumbing and appliances), carbon filter removes chloramines (improves taste, protects skin and hair), and RO provides safe, contaminant-free drinking water. Whole-house RO is a major investment (From $8,000 in Florida) and is primarily justified for well water with extremely high TDS (500+ ppm), high sodium from saltwater intrusion, or situations where the homeowner wants filtered water for bathing, laundry, and all uses. The production rate and waste water ratios of whole-house RO systems make them impractical for most city water applications. WaterLux will recommend the right configuration after testing your water.

What happens during a free water test from WaterLux?

A WaterLux free in-home water test measures hardness (GPG), pH, TDS (total dissolved solids), iron, chlorine/chloramine levels, and any other parameters relevant to your water source. The test takes about 30–45 minutes at your home, and you receive a written report with WaterLux's recommendations—with no obligation to purchase.

WaterLux's in-home water analysis is the starting point for every installation. A trained WaterLux water quality specialist visits your home, collects samples from your main drinking tap and (if applicable) your outdoor spigot or hose bib, and runs a battery of tests on-site. Standard measurements include: total hardness (GPG or ppm), pH, total dissolved solids (TDS), free chlorine and combined chlorines (chloramines), iron, turbidity, and sodium (where saltwater intrusion is suspected). For well water or homes with specific concerns, WaterLux can arrange lab testing for bacteria, nitrates, PFAS, heavy metals, and other parameters. You receive a written report you can keep, compare with your city's annual water quality report, or share with your doctor. If you choose to move forward with a WaterLux system, the test results inform exact system sizing and configuration—rather than a one-size-fits-all package.

Does hurricane season affect my home's water quality in South Florida?

Yes, hurricanes can temporarily compromise water quality in South Florida. Storm surges and flooding can push contaminants into municipal water systems. Power outages at treatment facilities may result in reduced treatment. Water main breaks from wind damage can introduce bacteria. An under-sink RO system or whole-house filtration system provides an additional layer of protection during these events.

During and after major hurricanes, South Florida homeowners frequently receive boil water notices from their utility provider. The three main risks are: (1) flooding and storm surge pushing agricultural chemicals, sewage, or bacteria into surface water sources used by treatment plants; (2) power outages at pumping stations reducing water pressure (low pressure can allow backflow contamination into pipes); and (3) physical damage to water mains allowing soil, bacteria, or debris to enter the distribution system. An in-home water treatment system provides meaningful protection during these events. A whole-house carbon filter reduces chemical contamination, while a water softener's bypass valve lets you isolate it from potentially contaminated water. An under-sink RO system provides the highest level of protection for drinking water during boil water notices—the 0.0001-micron membrane is effective against bacteria and most chemical contamination. WaterLux recommends keeping a 3-day supply of bottled water as additional precaution during named storms.

What is the difference between Broward County city water and private well water in South Florida?

Broward County city water is treated and regulated by the municipality—tested continuously, disinfected with chloramines, and partially softened before delivery. Well water is untreated groundwater that you are entirely responsible for testing and treating. City water in South Florida is typically hard (10.8–22.2 GPG before treatment); well water is harder (10.8–22.2 GPG before treatment) with additional issues including iron, sulfur, and bacteria.

The key differences affect what water treatment equipment is appropriate for your home. City water (municipal) is federally and state-regulated under the Safe Drinking Water Act, tested by the utility for 100+ parameters, disinfected (chloraminated in Pompano Beach), and reported annually. Its primary issues for homeowners are hardness, chloramines, disinfection byproducts, and trace PFAS. Well water in Broward County is entirely the homeowner's responsibility—no federal agency tests or treats it. The Biscayne aquifer in western Broward County produces water with very high hardness (often 10.8–22.2 GPG before treatment), elevated iron (>1 mg/L), hydrogen sulfide, and potentially bacteria or nitrates from agricultural sources. Unincorporated western Broward communities such as parts of Southwest Ranches, Davie, and western Coral Springs often rely on wells. Treatment for well water is more comprehensive and expensive than for city water. WaterLux tests both city and well water and designs systems appropriate to each source's actual chemistry.

What is the difference between a water softener and a water filter?

A water softener specifically removes hardness minerals (calcium and magnesium) through ion exchange. A water filter removes a broader range of contaminants—sediment, chlorine, chloramines, chemicals, PFAS, heavy metals, and biological contaminants—using media such as carbon or semipermeable membranes. Most South Florida homeowners benefit from both: a softener for hardness and a filter (carbon or RO) for chemical and taste concerns.

Water softeners and water filters serve different purposes and work through different mechanisms. A water softener targets the specific problem of hardness minerals and nothing else—it will not remove chlorine, PFAS, nitrates, or bacteria. A water filter uses various media (activated carbon, sediment media, RO membranes, UV light) to remove a wide range of contaminants depending on the technology. The most effective whole-home water treatment strategy for South Florida typically combines both: a whole-house carbon filter removes chloramines and disinfection byproducts from all household water; a water softener removes hardness minerals, protecting plumbing and appliances; and an under-sink RO system provides the highest purity water for drinking and cooking. Trying to 'filter' your way to soft water without a softener won't work—carbon filters do not remove hardness. Trying to 'soften' your way to pure drinking water won't work either—softeners do not remove PFAS or disinfection byproducts.

What is the best water treatment solution for South Florida homeowners?

The gold standard for South Florida homes on city water is a three-layer system: (1) a whole-house water softener to remove hardness and protect plumbing and appliances, (2) a whole-house carbon filter rated for chloramine removal to improve taste and protect skin and hair, and (3) an under-sink reverse osmosis system for pure drinking and cooking water. This combination addresses every major water quality concern in the Broward County area.

South Florida's water presents three distinct challenges that each require a specific solution. Challenge 1—Hard water (18.1 GPG before treatment): addressed by a salt-based water softener using ion exchange. This protects water heaters, dishwashers, washing machines, and plumbing from scale, and eliminates soap scum, hard water staining, and dry skin. Challenge 2—Chloramines and disinfection byproducts: addressed by a whole-house catalytic carbon filter. Chloramines cannot be removed by simply running water or by standard carbon—catalytic carbon (or activated carbon rated for chloramines) is required. Challenge 3—PFAS, trace contaminants, sodium, nitrates: addressed by an under-sink RO system for drinking and cooking water. A properly installed three-layer system from WaterLux creates genuinely different water quality throughout your home—water that is soft, free of chemical odors, and pure at the drinking tap. WaterLux designs and installs this complete solution with a single point of contact, a single warranty, and a single service plan.

How do I know if I need a water softener or a water filtration system in South Florida?

If you see scale on faucets, spots on dishes, soap scum on shower doors, or notice your skin feels dry after showering, you likely need a water softener. If your water has a chlorine or chemical taste, odor, or you're concerned about contaminants like PFAS or lead, you need a water filter. Most South Florida homeowners need both—and the only way to know for certain is a free water test.

The diagnostic signs for hard water versus chemical/contaminant water problems are usually distinct. Hard water symptoms: white or chalky scale buildup on faucet aerators, showerheads, and inside kettles; water spots on glasses and dishes even after washing; soap that doesn't lather well and leaves a residue; stiff, rough-feeling laundry; dry, itchy skin and dull hair after showering; reduced water flow from clogged aerators. Chemical/contaminant symptoms: chlorine or swimming-pool smell from tap water; bitter, metallic, or chemical taste in drinking water; concern about PFAS, lead, nitrates, or other invisible contaminants (which require lab testing to confirm). Because Broward County water has both hard water AND chloramine/chemical concerns, the vast majority of South Florida homeowners benefit from both a softener AND a filtration system. WaterLux's free water test definitively identifies both hardness levels and relevant contaminants, allowing an honest and specific recommendation.

Why WaterLux?

Concerned About PFAS in Your Water? Get a Free Test.

WaterLux offers a free in-home water test that screens for PFAS, hardness, chloramines, and other South Florida water issues. Our specialists will show you exactly what's in your water and recommend the most cost-effective solution.

Frequently Asked Questions

Are there PFAS in South Florida tap water?
PFAS have been detected in Broward County water supplies from the Biscayne Aquifer. The EPA set a maximum contaminant level of 4 parts per trillion in 2024. Only professional water testing can determine the exact levels in your home.
What type of filter removes PFAS from water?
Reverse osmosis systems remove 90-99% of PFAS from drinking water and are considered the gold standard for PFAS removal. Specialized activated carbon filters can also reduce PFAS levels. Standard pitcher filters are not effective against PFAS.
How much does a PFAS water filter cost in South Florida?
An under-sink reverse osmosis system for PFAS removal costs From $1,295 installed in South Florida. Whole-house carbon filtration systems range From $1,800. WaterLux offers free water testing to determine which system is right for your home.
Does WaterLux offer free water testing in South Florida?
Yes. WaterLux provides free professional water testing for South Florida homeowners. A technician tests your water on-site and explains exactly what contaminants are present and which treatment system is recommended. Call 754-317-0104 to schedule.
How long has WaterLux been serving Broward County?
WaterLux has been providing water treatment solutions across Broward County for over 14 years, serving South Florida families. We are an authorized Hague Quality Water dealer and Aquaphor distributor with a 4.9-star Google rating. Call 754-317-0104 for your free consultation.

Sources:

Ready for Better Water?

(754) 317-0104

waterlux.com — Free water test & consultation

4.9★ across 108 Google reviews · licensed & insured.

(754) 317-0104 Get your quote

https://waterlux.com/blog/pfas-water-filter-south-florida-2026